help with pinion??? (yokomo dib)

Post any modifications that you have to get your drivetrain and gearing setup get the most angle out of your chassis.

help with pinion??? (yokomo dib)

Postby Malice » Fri Jul 13, 2012 8:03 am

I need help, I'm stuck on the whole ratio thing and its winding me up!

ok specs

yokomo dib
yokomo 1.8 fcd
kawada 80t spur 38dp
tekin 7.5turn motor

what pinion size should i be running?? last night i ran on a track with a 34t pinion and the motor was getting hot... switched to a 90t spur and it was better but I'm running a 80t for body clearance...

can anyone help???
Malice
What's CS?
What's CS?
 
Posts: 4
Joined: Mon Jul 02, 2012 12:13 pm
Location: United Kingdom
Drift Chassis: Yokomo dib

Re: help with pinion??? (yokomo dib)

Postby FunkRenegade » Fri Jul 13, 2012 9:00 am

Right now, you're running 3.0fdr. Way too high for 7.5t motor. For your motor and 1.8 rear end, you want to use the biggest spur you can fit on the chassis. 80t is way too small. 7.5t motor should be geared around 7~ 7.5fdr. There's a chart in the manual that shows possible spur/pinion combo to reach that ratio.
FunkRenegade
Still Turns In
Still Turns In
 
Posts: 204
Joined: Sun Feb 19, 2012 8:24 pm
Location: Long Island
Drift Chassis: brokomo DIB

Re: help with pinion??? (yokomo dib)

Postby marshun » Fri Jul 13, 2012 9:05 pm

15 tooth!

im all about making my motor run as cool as possible. probably a preference. but i've had my motors for years. i use a 15 tooth and an 88 tooth spur. 2.0 or 100% cs
marshun
Still Turns In
Still Turns In
 
Posts: 198
Joined: Mon Feb 07, 2011 2:00 am
Location: hawaii
Drift Chassis: yokomo drift package

Re: help with pinion??? (yokomo dib)

Postby Dr.Fate » Fri Jul 13, 2012 9:27 pm

Okay I had that problem as well with 13.5! I went with 95t spur 18 combo with the 2.0 set up. Now I'm gonna under drive the front with a 40/14 F and 25/36 R. I seen some guy on youtube with a under driven chassis before with 10 degree castor blocks and it was sliding! Also I'm gonna do the FBD trick with the DIB.
Dr.Fate
Still Turns In
Still Turns In
 
Posts: 280
Joined: Fri Jan 28, 2011 1:12 pm
Location: San Diego
Drift Chassis: GPX-R, R31ML, OTA-ZEON & RWD D.D.C.

Re: help with pinion??? (yokomo dib)

Postby Stalwart » Fri Jul 13, 2012 10:05 pm

Get the biggest spur to clear the body, and smallest pinion to reach the spur without filing motor frame. Calculate FDR, test drive, and you'll know what pinion you need
User avatar
Stalwart
Still Turns In
Still Turns In
 
Posts: 171
Joined: Sun Jan 22, 2012 4:13 pm
Location: Latvia, Riga
Drift Chassis: Yokomo SD

Re: help with pinion??? (yokomo dib)

Postby FunkRenegade » Sat Jul 14, 2012 3:54 pm

OP is running 1.8 rear end. 2.0 internal ratio doesnt apply here. There is no black magic about gearing. Every motor turn has an optimal gearing range. Find out and gear your motor accordingly.
FunkRenegade
Still Turns In
Still Turns In
 
Posts: 204
Joined: Sun Feb 19, 2012 8:24 pm
Location: Long Island
Drift Chassis: brokomo DIB

Re: help with pinion??? (yokomo dib)

Postby marshun » Mon Jul 16, 2012 12:03 am

well i forgot to mention that my motor is an 8.5 turn brushless.

i use a 15tooth. its the lowest that is suggested for my motor. it said 15-20. but anything higher than 15 tooth and it gets hot after some time playing
marshun
Still Turns In
Still Turns In
 
Posts: 198
Joined: Mon Feb 07, 2011 2:00 am
Location: hawaii
Drift Chassis: yokomo drift package

Re: help with pinion??? (yokomo dib)

Postby nevuz » Mon Jul 30, 2012 1:22 am

I use the yokomo 2.0 fcd on my dib.
I currently use a 22T pinion and a 90t spur,but my motor(after a few minutes) is very hot
what pinion size should i be running?and the spur is ok?
nevuz
What's CS?
What's CS?
 
Posts: 2
Joined: Wed Jul 27, 2011 1:01 am
Location: North Italy
Drift Chassis: Yokomo DIB


Return to Drivetrain/ Gearing

Who is online

Users browsing this forum: No registered users and 1 guest

cron