HB Cyclone TC-H (Hiracchi Style) :D
-
- Rally Style Drifting
- Posts: 28
- Joined: Sun Jun 24, 2012 6:14 pm
- Drift Chassis: HB Cyclone TC
- Location: London, UK
Re: HB Cyclone TC-H (Hiracchi Style) :D
hey all could anyone point me in the direction of what pulleys will fit my cyclone?
-
- Rally Style Drifting
- Posts: 69
- Joined: Wed May 05, 2010 1:49 pm
- Drift Chassis: TEH-R31
- Location: Portugal
Re: HB Cyclone TC-H (Hiracchi Style) :D
pretty much anything with a 4mm bore
search the new 3racing pulleys and Broadtech sells nice pulleys too
search the new 3racing pulleys and Broadtech sells nice pulleys too
-
- Rally Style Drifting
- Posts: 28
- Joined: Sun Jun 24, 2012 6:14 pm
- Drift Chassis: HB Cyclone TC
- Location: London, UK
Re: HB Cyclone TC-H (Hiracchi Style) :D
cheers mate, know of anywhere that ships quick?
-
- Rally Style Drifting
- Posts: 69
- Joined: Wed May 05, 2010 1:49 pm
- Drift Chassis: TEH-R31
- Location: Portugal
Re: HB Cyclone TC-H (Hiracchi Style) :D
BroadTech ships very quickly...didn't try 3racing yet
-
- Rally Style Drifting
- Posts: 28
- Joined: Sun Jun 24, 2012 6:14 pm
- Drift Chassis: HB Cyclone TC
- Location: London, UK
Re: HB Cyclone TC-H (Hiracchi Style) :D
i had look through the broadtech site and i found this, says its for ta05 though http://www.broadtech.hk/eagleshop/shop/ ... 860P18-20T also,the ones i have mount via a bit with a grub screw, will they be the same, sorry about the noob questions, but i only ever had shaft/2wd cars before now
-
- Rally Style Drifting
- Posts: 69
- Joined: Wed May 05, 2010 1:49 pm
- Drift Chassis: TEH-R31
- Location: Portugal
Re: HB Cyclone TC-H (Hiracchi Style) :D
That one has a 4mm bore but is held by a 2mm pin
You can't use it unless your pulley shaft is like this:

You can't use it unless your pulley shaft is like this:

-
- Rally Style Drifting
- Posts: 28
- Joined: Sun Jun 24, 2012 6:14 pm
- Drift Chassis: HB Cyclone TC
- Location: London, UK
Re: HB Cyclone TC-H (Hiracchi Style) :D
ah thanks man, mine does have the pinholes a mm or two outside the spur holder but it also has indented sections either end for the grub screws like a motor shaft, should still work though it seems?
-
- Rally Style Drifting
- Posts: 69
- Joined: Wed May 05, 2010 1:49 pm
- Drift Chassis: TEH-R31
- Location: Portugal
Re: HB Cyclone TC-H (Hiracchi Style) :D
I think so
-
- Rally Style Drifting
- Posts: 28
- Joined: Sun Jun 24, 2012 6:14 pm
- Drift Chassis: HB Cyclone TC
- Location: London, UK
Re: HB Cyclone TC-H (Hiracchi Style) :D
just incase anyone else needs the same info, the 3racing pulleys are the perfect fit (4mm) 

Return to “Counter-Steer Full Setup”
Who is online
Users browsing this forum: No registered users and 2 guests